Journal

International Journal

• S.S.Han, H.K.Kim*, "Artificial neural network-based sequential approximate optimization of metal sheet architecture and forming process", Journal of Computational Design and Engineering, Volume 11, Issue 3, June 2024, Pages 265–279 (2024) https://doi.org/10.1093/jcde/qwae049 

• J.Lee, HK.Kim*, S.J.Heo, S.J.Lee, "Equivalent Stiffness Modeling Method of a Battery System for Evaluating Vehicle Rear-End Collision Performance", Int.J Automot. Technol. 24, 1325–1333 (2023) https://doi.org/10.1007/s12239-023-0107-5 

• S.S.Han, H.Eom, M.Lee, T.H.Yim, H.K.Kim*, "Design of wood-like metallic material using metal sheet architecture", Journal of Computational Design and Engineering, Volume 8, Issue 5, Pages 1290–1306 (2021) https://doi.org/10.1093/jcde/qwab048 

• K.H.You, H.K.Kim*, "A Study on the Effect of Process and Material Variables on the Hot Stamping Formability of Automotive Body Parts", Metals, 11(7), 1029 (2021) https://doi.org/10.3390/met11071029 

• D.K.Jung, S.H.Ha, H.K.Kim, Y.C.Shin, "Determination of Plastic Anisotropy of Extruded 7075 Aluminum Alloy Thick Plate for Simulation of Post-Extrusion Forming", Metals, 11(4), 641 (2021) https://doi.org/10.3390/met11040641 

• H.T.Jeong, H.K.Kim, W.J.Kim, "Processing maps (with flow instability criterion based on power-law breakdown) integrated into finite element simulations for evaluating the hot workability of 7075 aluminum alloy", Materials Today Communications, 27, 102254 (2021) https://doi.org/10.1016/j.mtcomm.2021.102254  

• Y.W.Jung,  H.K.Kim, "Prediction of Nonlinear Stiffness of Automotive Bushings by Artificial Neural Network Models Trained by Data from Finite Element Analysis", International Journal of Automotive Technology, 21(6), 1539-1551 (2020) https://doi.org/10.1007/s12239-020-0145-1  

• H.T.Jeong, H.K.Kim, H.Utsunomiya, E.Choi, W.J.Kim, "Fabrication of a thin open-cell Ni foam sheet with a high specific strength and moderate porosity using severe plastic deformation via differential speed rolling", Materials Science & Engineering A, 750, 7-13 (2019)

• H.K.Kim, W.J.Kim, "A Springback Prediction Model for Warm Forming of Aluminum Alloy Sheets Using Tangential Stresses on a Cross-Section of Sheet", Metals, 8(4), 257 (2018)

• H.K.Kim, H.B.Shim, B.S.Cha, G.H.Song, H.J.Kim, "Optimization of Initial Blank Shape for Minimizing the Trimming Process in Hot Stamping of T-shaped Parts", International Journal of Precision Engineering and Manufacturing, 19, 5, 721-728 (2018)

• S.J.Nam,  J.Y.Hwang, H.K.Kim, H.J.Choi, "Three-dimensional microstructure evolution and mechanical behavior of nanoporous Cu foams", Acta Materialia, 113, 170-179 (2016)

• P.T.L.Nguyen, J.Y.Lee, H.J.Yim, H.K.Kim. S.B.Lee, S.J.Heo, "Optimal Design of Vehicle Structure for Improving Small-Overlap Rating", International Journal of Automotive Technology, 16, 6, 959-965 (2015)

• J.Park, S.Lee, S.Kang, J.Jeon, S.H.Lee, H.K.Kim*, H.Choi*, "Complex effects of alloy composition and porosity on the phase transformations and mechanical properties of powder metallurgy steels", Powder Technology, 284, 459-466 (2015)

• M.J.Song, K.H.Kim, S.K.Hong, J.W.Lee, J.Y.Park, G.S.Yoon, H.K.Kim*, "Simulation-based Optimization of Cure Cycle of Large Area Compression Molding for LED Silicone Lens", Advances in Materials Science and Engineering, Volume 2015 (2015)

• Y.J.Jeon, M.J.Song, H.K.Kim, B.S.Chan, “The Effect of Hot-Stamping Process Conditions on the Changes in Material Strength”, International Journal of Automotive Technology, 16, 4, 619-627 (2015)

• H.K.Kim*, S.H.Lee, H. Choi, "Evaluation of Contact Heat Transfer Coefficient and Phase Transformation during Hot Stamping of a Hat-Type Part", Materials, 8, 2030-2042 (2015)

• D.Y.Kim, H.Y.Kim, S.H.Lee, H.K.Kim*, “Life Estimation of Hot Press Forming Die by Using Interface Heat Transfer Coefficient Obtained From Inverse Analysis”, International Journal of Automotive Technology, 16, 2, 285-292 (2015)

• M.J.Song, K.H.Kim, G.S.Yoon, H.P.Park, H.K.Kim*, “An Optimal Cure Process to Minimize Residual Void and Optical Birefringence for a LED Silicone Encapsulant”, Materials, 7, 4088-4104 (2014)

• M.J.Song, K.H.Kim, J.J.Kang, G.S.Yoon, H.K.Kim*, "FE analysis of cure-process-induced residual stress in light emitting diode encapsulant silicone resin considering mechanical property evolution", Advanced Science Letters, Volume 19, Issue 12, December 2013, Pages 3433-3440 (2013)

• H.K.Kim, M.J.Song, J.D.Kim, "An analytical multi-scale approach to describe deformation of nanocrystalline metals", Advanced Science Letters, Volume 19, Issue 12, December 2013, Pages 3541-3546  (2013)

• S.K.Hong, J.J.Kang, J.D.Kim, H.K.Kim, S.Y.Lee, C.H.Park. “Finite Element Analysis for the Tube Sinking Process of the Micro Ti-0.2Pd Tube”, Applied Mechanics and Materials, 465-466, 693-698 (2013)

• H.K.Kim*, S.I.Oh, "An interfacial energy incorporated couple stress crystal plasticity and the finite element simulation of grain subdivision", Journal of the Mechanics and Physics of Solids, 60, 1815-1841 (2012)

• G.H.Kim, G.S.Yoon, J.W.Lee, H.K.Kim, M.W.Cho, "A study on the micro-endmilling surface prediction model with non-dynamic errors", International Journal of Precision Engineering and Manufacture, 13, 11, 2035-2041 (2012)

• M.J.Song, K.H.Kim, G.S.Yoon, H.K.Kim*, "Multi-step cure process for void-free silicone resin encapsulant", Advanced Science Letters, Volume 13, June 2012, Pages 126-131 (2012)

• H.K.Kim, B.S..Cha, H.P.Park, B.O.Lee, M.J.Song, "A simulation of injection stretch-blow molding process by using a visco-plastic model ", Annual Technical Conference - ANTEC, Conference Proceedings , Volume 1, 2012, Pages 294-297 (2012)

• J.D.Kim, H.K.Kim, Y.M.Heo, S.H.Chang, "A study on the relation between die roll height and die chamfer shape in fine blanking for special gear", Advanced Materials Research, 320, 92-96 (2011)

• W.J.Kim, W.Y.Kim, H.K.Kim, "Hot-air Forming of Al-Mg-Cr Alloy and Prediction of Failure Based on Zener-Holloman Parameter", Metals and Materials International, 16, 6, 895-903 (2010)

• H.K.Kim*, W.J.Kim, "Failure prediction of magnesium alloy sheets deforming at warm temperatures using the Zener-Holloman parameter", Mechanics of Materials, 42, 293-303 (2010)

• W.J.Kim, S.J.Yoo, H.K.Kim, "Superplastic microforming of Mg-9Al-1Zn alloy with ultrafine-grained microstructure", Scripta Materialia, 59, 599-602 (2008)

• M.H.Lee, H.Y.Kim, H.K.Kim, G.D.Kim, S.I.Oh, "Non-Isothermal Simulation of Warm Circular Cup Deep Drawing Processing of an AZ31 Magnesium Alloy Sheet", Materials Transactions, 49, 5, 1120-1123 (2008)

• W.J.Kim, H.K.Kim, W.Y.Kim, S.W.Han, "Temperature and strain rate effect incorporated failure criteria for sheet forming of magnesium alloys", Materials Science and Engineering A,  488, 468-474 (2008)

• H.K.Kim*, S.K.Hong, "FEM-based optimum design of multi-stage deep drawing process of molybdenum sheet", Journal of Materials Processing Technology, 184, 354-362 (2007)

• K.H.Kim, H.K.Kim, S.I.Oh, "Deformation behavior of pure aluminum specimen composed of a few grains during simple compression", Journal of Materials Processing Technology, 171, 205-213 (2006)

• H.K.Kim*, S.I.Oh, "Finite element analysis of grain-by-grain deformation by crystal plasticity with couple stress", International Journal of Plasticity, 19, 1245-1270 (2003)

• H.K.Kim*, S.I.Oh, "Evaluation of heat transfer coefficient during heat treatment by inverse analysis", Journal of Materials Processing Technology, 112, 157-165 (2001)

Domestic Journal

• 황의찬, 이재준, 김흥규*, 장시열, 최웅철, "전방 및 기둥 측면 충돌 조건에서의 배터리 모듈 및 팩 경량화를 위한 최적 설계 연구", Transactions of KSAE, Vol. 32, No. 9, pp.751-764 (2024) DOI: https://doi.org/10.7467/KSAE.2024.32.9.751 

• 김종민, 김흥규, 장시열, "공랭식 배터리 팩 모듈의 채널 리브 형상에 따른 냉각 효율 향상 연구", Transactions of KSAE, Vol. 31, No. 4, pp.283-292 (2023) DOI: https://doi.org/10.7467/KSAE.2023.31.4.283 

• 이환주, 김흥규, 김동언, 전용준, 김봉구, 전채염, 금종원, "PA6 장섬유 강화 열가소성 복합소재의 압축성형으로 제작된 차량용 시트 백 프레임의 취출 온도에 따른 형상 정밀도 분석", Transactions of KSAE, Vol. 30, No. 2, pp.153-159 (2022) DOI: https://doi.org/10.7467/KSAE.2022.30.2.153 

• Y.Kim, H.K.Kim, "An Optimal Design of CFRP Prepreg Laminates for Automotive Roof Considering Structural Stiffness and Formability", Transactions of KSAE, Vol. 28, No. 10, pp.737-746, (2020) DOI: https://doi.org/10.7467/KSAE.2020.28.10.735 

• J.H.Kwag, H.S.Kook, H.K.Kim, H.C.Choi, W.H.Yang, "Feasibility study on neck defect inspection technique for press-formed products by using structural vibration measurement", J. Korean Society for Noise & Vibration Engineering, 28, 6, 721-727, 2018

• Y.J.Kim, S.H.Lee, H.K.Kim, "A Study on the Forming Analysis of Double-Dome model considering CFRP Prepreg Laminate Condition and Coefficient of Friction", J. Korea Society of Die & Mold Engineering, 10, 2, 12-17, 2016

• H.K.Kim, C.J.Jung, C.D.Cho, "Dynamic-Elastic Deformation Analysis for Precise Design of High Speed Press Machine", Trans. Korean Soc. Mech. Eng. A, 38, 1, 91-100, 2014

• D.G.Jeong, S.H.Kim, M.S.Kim, T.G.Lee, H.K.Kim, "Investigation of Shape Accuracy in the Forming of a Thin-walled S-rail with Classification of Springback Modes", Transactions of Materials Processing, 22, 8, 477-485, 2013

• B.H.Choi, S.H.Kim, H.K.Kim, "Quantitative Evaluation of Shape Accuracy in a Hat-type Product with UHSS according  to the Forming Procedure",  Journal of the Korean Society for Precision Engineering, 30, 10, 1111-1117, 2013

• B.H.Choi, J.W.Lee, S.H.Kim, M.G.Lee, H.K.Kim, "Comparison of Springback Modes in the Stamping Process  of an S-rail with HSS according to the Hardening Model", Transactions of Materials Processing, 22, 1, 30-35, 2013

• H.K.Kim, J.D.Kim, Y.M.Heo, W.J.Kim, "A comparative study of failure criteria for magnesium alloy sheet under warm press forming condition", Transactions of Materials Processing, 21, 2, 113-118, 2012

• M.J.Song, H.K.Kim, G.S.Yoon, K.H.Kim, "A multi step cure process to prevent residual bubbles in LED encapsulation silicone resin,  Transactions of Materials Processing, 21, 2, 101-106, 2012

• E.H.Kim, H.K.Kim, K.S.Seo, M.K.Lee, C.D.Cho, "Performance evaluation of a thermo siphon type radiator for LED lighting system by using an inverse heat transfer method,  Transactions of Materials Processing, 20, 7, 473-478, 2011

• M.J.Song, H.K.Kim, G.S.Yoon, K.H.Kim, "Elastic and viscoelastic warpage for LED encapsulation silicone considering cure reaction rate", Jounral of The Korea Society of Die & Mold Engineering, 5, 38-42, 2011

• J.D.Kim, H.K.Kim, "A study on the change of die roll size by the shape of die chamfer in fine blanking die for automobile door latch", Journal of Korea Academia-Industrial Cooperation Society, 12, 2, 565-570, 2011

• M.J.Song, H.K.Kim, J.J.Kang, K.H.Kim, "Finite element analysis of residual stress evolution during cure process of silicone resin for high-power LED encapsulant", Journal of the Korean Society for Precision Engineering, 28, 2, 219-225, 2011

• S.H.Chang, Y.M.Heo, K.H.Shin, H.K.Kim, Y.J.Jeon, "Study on the Friction Characteristics for AZ31 Sheet as Various Surface Treatment of SKD11", Transactions of Materials Processing, 19, 7, 429-434, 2010

• H.K.Kim, J.D.Kim, Y.M.Heo, "Warm formability variation of AZ31 sheet by double stage forming velocity", Transactions of Materials Processing, 18, 2, 112-115, 2009

• M.H.Lee, H.K.Kim, H.Y.Kim, S.I.Oh, "Evaluation on the formability of warm forming simulation of magnesium alloy sheet using FLD", Transactions of Materials Processing, 17, 7, 501-506, 2008

• M.H.Lee, H.Y.Kim, H.J.Kim, H.K.Kim, S.I.Oh, "Forming analysis for warm deep drawing process of magnesium alloy sheet", Transactions of Materials Processing, 16, 5, 401-405, 2007

• H.K.Kim, G.D.Kim, "Evaluation of formability sensitivity to die design in warm square cup deep drawing of AZ31 sheet", Transactions of Materials Processing, 16, 2, 120-125, 2007

• H.K.Kim, J.D.Kim, "Evaluation of warm deep drawability of magnesium alloy AZ31 sheet using solid-type lubricants", Transactions of Materials Processing, 15, 6, 453-458, 2006

• H.K.Kim, Y.B.Ko, J.J.Kang, Y.M.Heo, "4 inch wafer-scale replicability in hot embossing by using PDMS-cushioned Si mold", Journal of the Korean Society for Precision Engineering, 23, 8, 178-184, 2006

• H.K.Kim, W.R.Lee, S.K.Hong, J.D.Kim, B.K.Han, "Finite-element analysis of warm square cup deep drawing process of magnesium alloy AZ31 sheet", Transactions of Materials Processing, 15, 3, 232-240, 2006

• J.J.Kang, S.K.Hong, H.K.Kim, Y.M.Heo, "The effect of segmented blank holders on reducing asymmetric springback of anisotropic sheet metal in shallow-drawing", Transactions of Materials Processing, 14, 4, 392-398, 2005

• J.D.Kim, J.J.Kang, H.K.Kim, S.K.Hong, B.J.Kim, "A progressive fine blanking process design for forming of carrier plate", Transactions of Materials Processing, 14, 3, 207-214, 2005

• H.K.Kim, S.I.Oh, "Evaluation of heat transfer coefficient distribution by inverse analysis", Transactions of the KSME A, 20, 12, 3856-3870, 1996